Recycling of CDs

Tabletop stand for office supplies from the CD-ROM drive

What is needed:

- CD-drives - 7 pieces

- Hacksaw or substitutes: Jigsaw, a red-hot nail, the saw-Bulgarian - something which will be convenient to cut discs

- Pattern holders

- Sandpaper or a file for processing the edges.

 

• If the cut will be at home (on a table, stool, etc.) - a disc Put a cloth to avoid scratching the shiny surface of the disc with sawdust.
• If you decide to burn these slots, then the disc Put a Plotka and sufficient Tolt substrate, such as  corrugated board, so as not to burn the table.

1. Make a basic template.

Contours of the disk on the paper inside and out. As we enter the square circle drive. This will be the foundation of all templates. Next on the photos to be seen what will be left to finish.

2. Cut out the templates and with an awl or needle portable key points on the disks. Then, already on the disks themselves connect these dots and lines get cut.

a) It is a central part, call it A. Cut on one disc.

 

b) The central part B. Also in single copy.

 

c) Bottom (denoted just in case). One detail.

 

d) Lateral G. They must be on two discs.

d) And last, the lateral part of the D, too, the two parts. (Actually it is one in a cut as the central part of A. .. just noticed , So that you can simply cut the three central part A).

3. Now take a hacksaw, jigsaw (I'm in this time a hot fragment of cloth from the jigsaw make a hole - it seemed more convenient) and start sawing on the planned lines. You should get something like this:

Bits of the picture - this is the disc otkolupnulsya shiny coat.

That's the bottom will look like.

• Note: that after the assembly design is not distorted and will last longer, the thickness of the cut should not be thinner than the thickness of the disk, and the need to cut as much as possible straight lines - no curves and waves.
  
• Second note: The disc may break during cutting. Therefore Perform disk so that it is only a few millimeters was for the working surface on which the sawing .

4. Burrs process nozhdachnoy paper. To not see the inscriptions on the obverse side of a disc, cover them with paint. For example, silver from a container.

5. Assembling the Stand:

a) A central part of the line with the central part B:

b) In the remaining sections in the central part of the B vstarlyaem bokovinki W:

c) Merging the resulting design with the remaining bokovinkami:

so

 

And so

 

Stand almost ready, lacking only the bottom:

 (This is a bottom view)

d) Put on the bottom in:

Overturn

Photo above:

Shoes handmade: art work

 

    

Những đôi giầy da độc đáo

Found on the "Etsi". One aunt makes and sells. And many more such interesting shoes here. And these purple I just conquered.Behold, now I sit and I want them. But prices there are, of course, not local. These shoes almost 317 dollars worth. I think they are worth it, but I'm still only on the pictures to admire.

BEADED TREE OF LIFE PENDANT TUTORIAL

Please note this is an intermediate project. Materials:  One 6mm Soldered Ring 4" 16g Sterling Wire 3ft 24g Soft Sterling Wire - cut into four 9" pieces Assorted Gemstones chips - in leaf colors Tools:  1" diameter Dowel or Pipe Wire Cutter Chain-Nose Pliers Step 1 – Using the dowel or pipe as your form, bend the 16g wire around and cut to create a complete circle. Step 2 – Slide the 6mm soldered ring onto the loop you create with the heavier wire. Step 3 - Anchor the 4 pieces of 24g wire to the bottom of the loop by wrapping several time around. (This will also hide ends where they meet on the wire frame.) Step 4 – Twist the wires together to create a trunk. This should be about 1/2" or half the diameter of the circle. Step 5 – Add the stone chips to the wires and weave* them to create the branches. Create a small loop at then end of each wire after the chips so they don't fall off. *You can simply cross the beaded wires to create fullness. Step 6 – Wrap the end of the wire around the frame to anchor. Make sure you capture the soldered ring in the center as you do this so your pendant hangs properly. Step 7 – Trim the ends and tuck down into the direction of the wire.

Jewellery hand made with love

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.