How to sew evening dress

Modeling red dresses.

Construction and sewing a pink dress with ruffles

Hướng dẫn may áo thời trang cho mẹ

Mum Shirt transfer to baby Dress

This is a super simple project that took about 30 minutes to do.

Here is the shirt I started with.

Cut off the sleeves.

Cut the shoulder strap about 1.5  inches before the seam on the front of the shirt.

Then I put the shirt on Aiyanna and pinned the sides to fit. I played with the straps until I liked how it looked.

Using my pins as guides I cut the sides of the shirt.

I french seamed the sides and finished the arm holes.

Then I sewed the straps to the front and hemmed the bottom to shorten it some. I left the original hem so I can let it out as she gets taller.

Chandelier made of rose and bead

 

Làm đèn, chuông gió bằng hoa hồng và cườm

Interior decoration - suspension of roses and beads

Under the cut is a job description. Just strange it is for some. Very detailed in what order to string beads. But of all the rest of the word literally. And about how to make rosettes directly - not even a hint. Okay, we'll win it. But very little thing is even cute.

Beading Gladiolus tutorial

 Hướng dẫn kết hoa lay ơn bằng cườm

Gladiolus

Photo1

Photo2

Photo3

Photo4

Photo5

Photo6

Photo7

Photo8

How to bead roses

At the rosette must weave 6 small petals, and 6 more. 

They weave the same, only with different numbers of beads.

This entry sequence set beads:

On the small petals: 6,7,8,8,7,6,5.

Long-petals: 9,10,10,9,8,7,6.

On the wire length of 35cm, stringing one by one the number of beads that in the description.

Describe more petal: 
Bend the wire in half to determine the middle and dialing 9 beads (this is the first digit in the description)

Then recruit 10 more beads, but so that they are not connected to once again do not count

One end of the wire cuff in the opposite direction

And contracts as follows:

Make sure the ends of the wires were of equal length.

Rows of beads lie parallel to each other, hence the name of art. 
Further continue in the same order of writing: 9.10 We strung and beyond: 10,9,8,7,6. 
And we get here is a tab - there should be six.

Also supplied with small petals. They too should be six.

When the petals are ready, gather roses: 3 small petal twists along the convex surface outward, and so all the petals. In each row of 3 petals and relative to the previous row in a staggered manner.
That's what happens:

Now the gossiping under green rosettes corolla (in false color of the fabric is called pasting). Leaves are different and the Scourge of writing:

Small: 1,2,3,3,2,1 - 3shtuki.

Large: 1,2,1,2,3,3,2,1 -2 pc.

Now attach to the rosettes on the lower side as follows:

Now the leaves on the stem: 1,3,5,7,7,7,6,5,4,3,1. (Number optional) 
Collect and 3 petals together: one or two lower. (No pictures forgot to photograph)

The result:

Recycling of CDs

Tabletop stand for office supplies from the CD-ROM drive

What is needed:

- CD-drives - 7 pieces

- Hacksaw or substitutes: Jigsaw, a red-hot nail, the saw-Bulgarian - something which will be convenient to cut discs

- Pattern holders

- Sandpaper or a file for processing the edges.

 

• If the cut will be at home (on a table, stool, etc.) - a disc Put a cloth to avoid scratching the shiny surface of the disc with sawdust.
• If you decide to burn these slots, then the disc Put a Plotka and sufficient Tolt substrate, such as  corrugated board, so as not to burn the table.

1. Make a basic template.

Contours of the disk on the paper inside and out. As we enter the square circle drive. This will be the foundation of all templates. Next on the photos to be seen what will be left to finish.

2. Cut out the templates and with an awl or needle portable key points on the disks. Then, already on the disks themselves connect these dots and lines get cut.

a) It is a central part, call it A. Cut on one disc.

 

b) The central part B. Also in single copy.

 

c) Bottom (denoted just in case). One detail.

 

d) Lateral G. They must be on two discs.

d) And last, the lateral part of the D, too, the two parts. (Actually it is one in a cut as the central part of A. .. just noticed , So that you can simply cut the three central part A).

3. Now take a hacksaw, jigsaw (I'm in this time a hot fragment of cloth from the jigsaw make a hole - it seemed more convenient) and start sawing on the planned lines. You should get something like this:

Bits of the picture - this is the disc otkolupnulsya shiny coat.

That's the bottom will look like.

• Note: that after the assembly design is not distorted and will last longer, the thickness of the cut should not be thinner than the thickness of the disk, and the need to cut as much as possible straight lines - no curves and waves.
  
• Second note: The disc may break during cutting. Therefore Perform disk so that it is only a few millimeters was for the working surface on which the sawing .

4. Burrs process nozhdachnoy paper. To not see the inscriptions on the obverse side of a disc, cover them with paint. For example, silver from a container.

5. Assembling the Stand:

a) A central part of the line with the central part B:

b) In the remaining sections in the central part of the B vstarlyaem bokovinki W:

c) Merging the resulting design with the remaining bokovinkami:

so

 

And so

 

Stand almost ready, lacking only the bottom:

 (This is a bottom view)

d) Put on the bottom in:

Overturn

Photo above: